Low voltage detection

Anobium — Thu, 19 Feb 2026 07:29:19 -0000

Play with this.

#chip 18f24q10
#option Explicit


    DIM ADCValue AS WORD
    DIM ReadVDDmV AS WORD

    FVRInitialize ( FVR_off )
    ' --------------------------------------------------------
    ' Enable FVR at 1.024V
    ' FVRCON:
    ' bit7 FVREN = 1 (enable)
    ' bit6 FVRRDY = read-only (wait until 1)
    ' bit1-0 ADFVR = 01 (1.024V)
    ' --------------------------------------------------------
    FVRInitialize ( FVR_1x )

    ' Wait for FVR to stabilise
    wait while FVRIsOutputReady = false

    ' Read ADC
    ADCValue = READAD10( AN0 )

    ' --------------------------------------------------------
    ' Compute VDD in millivolts:
    ' VDDmV = (1023 * 1024) / ADCValue
    ' 1023 * 1024 = 1,047,552 fits in LONG
    ' --------------------------------------------------------

    ReadVDDmV = ( 1023 * 1024 ) / ADCValue

Low voltage detection

Roger Jönsson — Wed, 18 Feb 2026 22:43:00 -0000

(I guess):
You can set the PIC18F24Q10 ADC to use VDD as reference, then use the ADC to measure one of the internal voltage reference sources?

Low voltage detection

Fabrice Engel — Tue, 10 Feb 2026 05:33:59 -0000

Hi Jose,

I cross my fingers that you will find the way to test Vdd. If you are looking for more content round the ADC management and how I used it, you can have a look in the full source code of my project.
The source code is documented line by line, so I guess you will be able to better understand how I used it myself and how I was able shutoff the circuitry ordered from the microcontroller.

The full project page is on Elektor here:
https://www.elektormagazine.com/labs/short-circuit-probe

Or on PCBWay here:
https://www.pcbway.com/project/shareproject/Short_Circuit_Probe_f5e16641.html

Low voltage detection

Jose Houle — Mon, 09 Feb 2026 17:07:31 -0000

Hello Fabrice
Thank you so much for your reply !!

I can't wait to try it later today !!

Thanks !!!

Low voltage detection

Fabrice Engel — Sun, 08 Feb 2026 14:59:50 -0000

btw, probably you noticed, the PIC used in my circuit is a PIC16F1825

Low voltage detection

Anobium — Sun, 08 Feb 2026 14:52:32 -0000

:-)

Low voltage detection

Fabrice Engel — Sun, 08 Feb 2026 14:45:21 -0000

Hello,

I used internal voltage reference to read the battery voltage of my circuit (Short Circuit Probe).
If you read the Vdd voltage by using 2 resistors as voltage dividor, would that be work?
But maybe I miss something from your question.

Here the function I created (Sorry Anobium, I was using my own ADC routine and not the build in from GCBasic):

// Procedure to read AN3 analog values - 10 bits resolution for Battery voltage
// This Function is not portable like that to other microcontroller because of non using GCBASIC internal ADC commands

Function myBatteryReadAD10() As Word                                     // Port RA4 - AN3 is hardcoded inside the procedure, this code is not portable per default   
    FVRCON = 0b10000010                                                  // FVREN is activated and set to 2.048V (page 142)
    ADCON1 = 0b10010011                                                  // ADFM right justified, ADC conversion clock @Fosc/8, Vref- at Gnd, Vref+ at FVR 2.048V (page 151), voltage divider 0,32
    Set ANSELA.4 On                                                      // Define Port RA4 as Analog input (page 123)
    ADCON0 = 0b00001101                                                  // AN3 (RA4) actif, ADC is enabled (page 150)
    Wait 25 us                                                           // Wait 25µs to let charge capacitor (time could be increased!) - (see more page 154)
    // But FVRRDY is always ON on PIC16F1825 according note 1 page 142, anyway keep the instruction in the code for education and experience !
    Wait While FVRCON.FVRRDY OFF                                         // Wait until internal voltage reference is ready (previously cleared in the procedure by set FVRCON), 
    SET GO_NOT_DONE ON                                                   // Start the Analog Digital conversion
    Wait While GO_NOT_DONE ON                                            // We are waiting up conversion is completed, this is a blocking routine waiting on the flag 
    SET ADCON0.ADON OFF                                                  // Deactivate the ADC 
    myBatteryReadAD10 = ADRESL                                           // Copy LSB into low part variable to send back from function ADC value is 10 bits length (page 149)
    myBatteryReadAD10_H = ADRESH                                         // Copy MSB into high part variable to send back from function ADC value is 10 bits length (page 149)
    FVRCON = 0b00000010                                                  // FVREN is deactivated (page 142)   
End Function

Low voltage detection

Jose Houle — Sun, 08 Feb 2026 13:37:32 -0000

hello guys,
I need your help
I can't find a way to measure Vdd and compare it to a generated voltage reference..

I want to set off every output is a short circuit happen.
so I need to detect Vdd dropping to low..

im using PIC18F24Q10

please help me
I'm frustrated on chatgpt :)
José

Recent posts to Low voltage detection

Low voltage detection

Low voltage detection

Low voltage detection

Low voltage detection

Low voltage detection

Low voltage detection

Low voltage detection

Low voltage detection